Common marble construction process<\/h3>\n\n- coarse grinding stage<\/strong>(50#~300#): Dry grinding or semi-dry\/semi-wet grinding can be performed first (to reduce water penetration and avoid alkali reaction and yellowing later).<\/li>\n
- From medium to fine grinding<\/strong>\uff08300#~3000#\uff09\uff1aWet grinding is necessary.<\/strong>Almost all professional technicians will add water.<\/li>\n
- Final polishing\/crystallization<\/strong>Use a soft pad + crystal hardener, usually with a small amount of water or dry polishing.<\/li>\n<\/ul>\n
Water-polished vs. dry-polished pads comparison chart (marble perspective)<\/h3>\n\n\n\n\nproject<\/th>\n Wet grinding pads<\/th>\n Dry grinding discs (dry grinding)<\/th>\n Marble Recommendation<\/th>\n<\/tr>\n<\/thead>\n \n\nHeat dissipation effect<\/td>\n very good<\/td>\n Normal (easily gets hot)<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nStone damage risk<\/td>\n Low (not easy to burn\/discolor)<\/td>\n Higher (white marble is most prone to yellowing when burned).<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \ndust<\/td>\n Almost no (slurry)<\/td>\n Extremely large (requires powerful vacuuming)<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nGloss\/Smoothness<\/td>\n Better and easier to get out of the mirror<\/td>\n Slightly inferior, prone to leaving marks<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nGrinding disc life<\/td>\n Longer<\/td>\n shorter<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nprice<\/td>\n Cheap<\/td>\n Obviously expensive<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nDisease risk<\/td>\n High risk (waterproofing is necessary beforehand)<\/td>\n Lower (high temperature forces out water vapor)<\/td>\n Dry grinding is slightly better<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\nOnly in very special circumstances should full dry grinding be considered.<\/strong>The site must not be flooded, there is valuable wood veneer nearby, and there is a risk of serious blockage of the sewers.<\/p>\nII. Tile Grinding: Wet grinding throughout the entire process is also highly recommended.<\/h2>\n
One-sentence conclusion<\/strong>Tiles are hard, but they are more susceptible to damage from high temperatures that could burn the glaze.90%+ of renovations use wet sanding with water-based grinding pads.<\/strong>most.<\/p>\n(Similar to the comparison table for marble, wet polishing has more obvious advantages on ceramic tiles: less chipping and less yellowing of the glaze.)<\/p>\n
Dry grinding throughout the entire process is not recommended.<\/strong>Unless the site is extremely dry, dry grinding of light-colored tiles can easily cause problems.<\/p>\nIII. Which materials are best suited for dry grinding? (The preferred scenario for dry grinding pads)<\/h2>\n
The best materials for dry grinding (recommended from highest to lowest)<\/strong>\uff1a<\/p>\n\n- Granite (Artificial Stone) \u2605\u2605\u2605\u2605\u2605 Can be dry-ground throughout the process, heat resistant, and does not easily discolor.<\/li>\n
- Artificial stone\/quartz stone \u2605\u2605\u2605\u2605\u2606 High density, heat resistant<\/li>\n
- Microcrystalline stone\/microcrystalline glass \u2605\u2605\u2605\u2605\u2606 Extremely hard, excellent dry polishing for a mirror finish<\/li>\n
- Dark-colored vitrified tiles\/unglazed tiles \u2605\u2605\u2605\u2606\u2606 (Light colors should be used with caution)<\/li>\n
- Concrete sealing and curing floor \u2605\u2605\u2605\u2606\u2606<\/li>\n<\/ol>\n
Marble & Light-colored Tiles<\/strong>Dry grinding is highly discouraged and not recommended for use throughout the entire process.<\/p>\nIV. Can all surfaces be water-polished?Answer: Absolutely not!<\/strong><\/h2>\nSuitable for wet polishing (mainstream stone types)<\/strong>\uff1a<\/p>\n\n- Marble, ceramic tile, granite, artificial stone, microcrystalline stone<\/li>\n
- Concrete, terrazzo, etc.<\/li>\n<\/ul>\n
Wet grinding is strictly prohibited (it will directly damage the material).<\/strong>\uff1a<\/p>\n\n- Solid wood\/engineered wood flooring \u2192 absorbs water, swells, warps, and molds.<\/li>\n
- Carpets \u2192 Thoroughly soaked, breeding bacteria<\/li>\n
- Metal floors (stainless steel, etc.) \u2192 rust and corrosion<\/li>\n
- Bamboo flooring, some PVC flooring, and floors in precision instrument rooms \u2192 susceptible to water penetration.<\/li>\n<\/ul>\n
V. Final Summary (Just memorize it and you'll be fine)<\/h2>\n\n- Stone\/Ceramic Tiles: Bright, Smooth, and Safe<\/strong> \u2192 Wet grinding pads + wet grinding (preferred)<\/strong><\/li>\n
- Super heat resistant + Must not be exposed to water on site<\/strong> \u2192 Dry grinding disc<\/strong>(Granite\/quartz, etc.)<\/li>\n
- Wood \/ Carpet \/ Metal<\/strong> \u2192 Wet grinding is prohibited.<\/strong>Only dry or other methods are possible.<\/li>\n<\/ul>\n
Tips\uff1a<\/strong>
\nWet polishing = clean, high-gloss, and safe, but water usage must be carefully controlled.
\nDry grinding is flexible and free from water damage, but it produces a lot of dust, so proper protective measures are necessary.\n<\/p>\n\n <\/p>\n\n Recommended purchase: SPTA 15-pack of water-based resurfacing tablets!\n <\/p>\n
Water-polished vs. dry-polished pads comparison chart (marble perspective)<\/h3>\n\n\n\n\nproject<\/th>\n Wet grinding pads<\/th>\n Dry grinding discs (dry grinding)<\/th>\n Marble Recommendation<\/th>\n<\/tr>\n<\/thead>\n \n\nHeat dissipation effect<\/td>\n very good<\/td>\n Normal (easily gets hot)<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nStone damage risk<\/td>\n Low (not easy to burn\/discolor)<\/td>\n Higher (white marble is most prone to yellowing when burned).<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \ndust<\/td>\n Almost no (slurry)<\/td>\n Extremely large (requires powerful vacuuming)<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nGloss\/Smoothness<\/td>\n Better and easier to get out of the mirror<\/td>\n Slightly inferior, prone to leaving marks<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nGrinding disc life<\/td>\n Longer<\/td>\n shorter<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nprice<\/td>\n Cheap<\/td>\n Obviously expensive<\/td>\n Water milling wins hands down<\/td>\n<\/tr>\n \nDisease risk<\/td>\n High risk (waterproofing is necessary beforehand)<\/td>\n Lower (high temperature forces out water vapor)<\/td>\n Dry grinding is slightly better<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\nOnly in very special circumstances should full dry grinding be considered.<\/strong>The site must not be flooded, there is valuable wood veneer nearby, and there is a risk of serious blockage of the sewers.<\/p>\nII. Tile Grinding: Wet grinding throughout the entire process is also highly recommended.<\/h2>\n
One-sentence conclusion<\/strong>Tiles are hard, but they are more susceptible to damage from high temperatures that could burn the glaze.90%+ of renovations use wet sanding with water-based grinding pads.<\/strong>most.<\/p>\n(Similar to the comparison table for marble, wet polishing has more obvious advantages on ceramic tiles: less chipping and less yellowing of the glaze.)<\/p>\n
Dry grinding throughout the entire process is not recommended.<\/strong>Unless the site is extremely dry, dry grinding of light-colored tiles can easily cause problems.<\/p>\nIII. Which materials are best suited for dry grinding? (The preferred scenario for dry grinding pads)<\/h2>\n
The best materials for dry grinding (recommended from highest to lowest)<\/strong>\uff1a<\/p>\n\n- Granite (Artificial Stone) \u2605\u2605\u2605\u2605\u2605 Can be dry-ground throughout the process, heat resistant, and does not easily discolor.<\/li>\n
- Artificial stone\/quartz stone \u2605\u2605\u2605\u2605\u2606 High density, heat resistant<\/li>\n
- Microcrystalline stone\/microcrystalline glass \u2605\u2605\u2605\u2605\u2606 Extremely hard, excellent dry polishing for a mirror finish<\/li>\n
- Dark-colored vitrified tiles\/unglazed tiles \u2605\u2605\u2605\u2606\u2606 (Light colors should be used with caution)<\/li>\n
- Concrete sealing and curing floor \u2605\u2605\u2605\u2606\u2606<\/li>\n<\/ol>\n
Marble & Light-colored Tiles<\/strong>Dry grinding is highly discouraged and not recommended for use throughout the entire process.<\/p>\nIV. Can all surfaces be water-polished?Answer: Absolutely not!<\/strong><\/h2>\nSuitable for wet polishing (mainstream stone types)<\/strong>\uff1a<\/p>\n\n- Marble, ceramic tile, granite, artificial stone, microcrystalline stone<\/li>\n
- Concrete, terrazzo, etc.<\/li>\n<\/ul>\n
Wet grinding is strictly prohibited (it will directly damage the material).<\/strong>\uff1a<\/p>\n\n- Solid wood\/engineered wood flooring \u2192 absorbs water, swells, warps, and molds.<\/li>\n
- Carpets \u2192 Thoroughly soaked, breeding bacteria<\/li>\n
- Metal floors (stainless steel, etc.) \u2192 rust and corrosion<\/li>\n
- Bamboo flooring, some PVC flooring, and floors in precision instrument rooms \u2192 susceptible to water penetration.<\/li>\n<\/ul>\n
V. Final Summary (Just memorize it and you'll be fine)<\/h2>\n\n- Stone\/Ceramic Tiles: Bright, Smooth, and Safe<\/strong> \u2192 Wet grinding pads + wet grinding (preferred)<\/strong><\/li>\n
- Super heat resistant + Must not be exposed to water on site<\/strong> \u2192 Dry grinding disc<\/strong>(Granite\/quartz, etc.)<\/li>\n
- Wood \/ Carpet \/ Metal<\/strong> \u2192 Wet grinding is prohibited.<\/strong>Only dry or other methods are possible.<\/li>\n<\/ul>\n
Tips\uff1a<\/strong>
\nWet polishing = clean, high-gloss, and safe, but water usage must be carefully controlled.
\nDry grinding is flexible and free from water damage, but it produces a lot of dust, so proper protective measures are necessary.\n<\/p>\n\n <\/p>\n\n Recommended purchase: SPTA 15-pack of water-based resurfacing tablets!\n <\/p>\n
| project<\/th>\n | Wet grinding pads<\/th>\n | Dry grinding discs (dry grinding)<\/th>\n | Marble Recommendation<\/th>\n<\/tr>\n<\/thead>\n |
|---|---|---|---|
| Heat dissipation effect<\/td>\n | very good<\/td>\n | Normal (easily gets hot)<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| Stone damage risk<\/td>\n | Low (not easy to burn\/discolor)<\/td>\n | Higher (white marble is most prone to yellowing when burned).<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| dust<\/td>\n | Almost no (slurry)<\/td>\n | Extremely large (requires powerful vacuuming)<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| Gloss\/Smoothness<\/td>\n | Better and easier to get out of the mirror<\/td>\n | Slightly inferior, prone to leaving marks<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| Grinding disc life<\/td>\n | Longer<\/td>\n | shorter<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| price<\/td>\n | Cheap<\/td>\n | Obviously expensive<\/td>\n | Water milling wins hands down<\/td>\n<\/tr>\n |
| Disease risk<\/td>\n | High risk (waterproofing is necessary beforehand)<\/td>\n | Lower (high temperature forces out water vapor)<\/td>\n | Dry grinding is slightly better<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n Only in very special circumstances should full dry grinding be considered.<\/strong>The site must not be flooded, there is valuable wood veneer nearby, and there is a risk of serious blockage of the sewers.<\/p>\n One-sentence conclusion<\/strong>Tiles are hard, but they are more susceptible to damage from high temperatures that could burn the glaze.90%+ of renovations use wet sanding with water-based grinding pads.<\/strong>most.<\/p>\n (Similar to the comparison table for marble, wet polishing has more obvious advantages on ceramic tiles: less chipping and less yellowing of the glaze.)<\/p>\n Dry grinding throughout the entire process is not recommended.<\/strong>Unless the site is extremely dry, dry grinding of light-colored tiles can easily cause problems.<\/p>\n The best materials for dry grinding (recommended from highest to lowest)<\/strong>\uff1a<\/p>\n Marble & Light-colored Tiles<\/strong>Dry grinding is highly discouraged and not recommended for use throughout the entire process.<\/p>\n Suitable for wet polishing (mainstream stone types)<\/strong>\uff1a<\/p>\n Wet grinding is strictly prohibited (it will directly damage the material).<\/strong>\uff1a<\/p>\n Tips\uff1a<\/strong> \n Recommended purchase: SPTA 15-pack of water-based resurfacing tablets!\n <\/p>\n |
![\"Marbrofin](\"https:\/\/m.media-amazon.com\/images\/I\/81Z3aP6CYHL._AC_SX679_PIbundle-15,TopRight,0,0_SH20_.jpg\")